BEC 5102 Series Bedienungsanleitung

BIPAC 5102 Series (802.11g) ADSL2+ Modem/Router User’s Manual

2.3 The Front LEDs BIPAC 5102 BIPAC 5102S BIPAC 5102G LED Meaning 1 PPP : Lit steady when there is a PPPoA / PPPoE connection. 2 ADSL: Lit w

2.4 The Rear Ports BIPAC 5102 4312BIPAC 5102S 4312BIPAC 5102G 43512 Port Meaning 1 PWR Connect the supplied power adapter to this jack. 2 RESE

2.5 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front

Chapter 3 Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the follo

Configuring PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double

Configuring PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. D

Configuring PC in Windows 98/Me 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration

Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab

3.2 Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface: Username: admin Password:

3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port WAN Port

Chapter 1 ... 1 1.1 Introducing the BIPAC 5102 Series...

3.5 Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a

Chapter 4 Configuration At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired set

4.1 Quick Start For detailed instructions on configuring WAN settings, see the Interface Setup section of this manual. The information you need for t

Step1. Set your new password. Step2: Choose your time zone 21

Step3: Set your Internet connection 22

23

Step4: Restart your ADSL Router 24

4.2 Interface Setup Click this item to access the following sub-items that configure the ADSL router: Internet, LAN, and Wireless These functions are

4.2.1 Internet ATM VC Virtual Circuit: VPI (Virtual Path Identifier) and VCI (Virtual Channel Identifier) define a virtual circuit. VPI: The vali

VCI: The valid range for the VCI is 32 to 65535. Enter the VCI assigned to you. This field may already be configured. ATM QoS: Select CBR to specify

Chapter 1 Introduction the BIPAC 5102 Series 1.1 Introducing the BIPAC 5102 Series Welcome to the Billion BIPAC 5102 Series ADSL2+ Router. Your Billio

Dynamic Route: RIP Version: Select the RIP version from RIP-1, RIP-2B and RIP-2M. RIP Direction: Select the RIP direction from None, Both, In Only an

4.2.2 LAN A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usual

DHCP DHCP (Dynamic Host Configuration Protocol, RFC 2131 and RFC 2132) allows individual clients to obtain TCP/IP configuration at start-up from a se

4.2.3 Wireless 802.11g is only supported for the BiPAC 5102G . This section introduces the wireless LAN and some basic configurations. Wireless L

Wireless LAN Access Point: Default setting is set to Activated. If you do not have any wireless, both 802.11g and 802.11b, device in your network,

both 11g and 11b devices in your network, then keep the default in mixed mode. From the drop-down manual, you can select 802.11g if you have only 11g

("0-9", "A-F"). You must configure all four keys, but only one key can be activated at any one time. The default key is key 1. W

4.3 Advanced Setup 4.3.1 Routing If you have another router with a LAN-to-LAN connection, you may create a static routing on the router that is the ga

ADD Route Destination IP Address：This is the destination subnet IP address. IP Subnet Mask：It is the destination IP addresses based on above desti

4.3.2 NAT The NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet. The default setting is Dyn

to target a machine on your network. Secondly, it can block and redirect certain ports to limit the services that outside users can access. For exam

DMZ:  Disabled: As set in default setting, it disables the DMZ function.  Enabled: It activates your DMZ function. DMZ Host Address: Give a

The device can be configured as a virtual server so that remote users accessing services such as Web or FTP services via the public (WAN) IP address c

Rule Index: Choose the rule number. Rule Type: One-to-one: This is the mode maps one local IP address to one global IP address. Note that port numb

Public Start IP: This is the starting Inside Public IP Address. Enter 0.0.0.0 here if you have a dynamic IP address from your ISP. Public End IP: Th

4.3.3 ADSL ADSL Mode: The default setting is Auto Sync-UP. This mode will automatically detect your ADSL, ADSL2+, ADSL2, G.dmt, G.lite, and T1.413.

4.4 Access Management 4.4.1 ACL Access Control Listing allows you to determine which services/protocols can access which BIPAC 5102 Series interface f

4.4.2 IP Filter You may use telnet or Web to remotely manage the ADSL Router. User just needs to enable Telnet or Web and give it an IP address that w

IP Filter Rule Index: This is item number Active: Select Yes from the drop down list box to enable IP filter rule. Source IP Address: The source IP

4.4.3 SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. SNMP is a membe

4.4.4 UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP

1.2 Features of the BIPAC 5102 Series ADSL Multi-Mode Standard supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. It als

4.4.5 DDNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a sta

4.5 Maintenance 4.5.1 Administrator In factory setting, the default password is admin, and that for user is also password. You can change the default

4.5.2 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time

4.5.3 Firmware Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedic

DO NOT power down the router or interrupt the firmware upgrading whileit is still in process. Improper operation could damage the router. Warn

4.5.4 SysRestart Click SysRestart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to rest

4.5.6 Diagnostics The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN s

4.6 Status 4.6.1 Device Info Device Information Firmware version: This is the Firmware version MAC Address: This is the MAC Address LAN IP Addre

WAN Status: “Not connected” or “Connected” Virtual Circuit: There are eight groups of PVC can be defined. VPI: The valid range for the VPI is 0 to

4.6.2 System Log Display system logs accumulated up to the present time. You can trace historical information with this function. 57

(ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Net2phone, Ping, NetMeeting, IP phone and others. Firewall Supports simple

4.6.3 Statistics Read-only information here includes port status and packet specific statistics. Also provided are "Transmit Statistics" and

ADSL Transmit total PDUs: This field displays the number of total PDU transmitted in the last second. Transmit total Error Counts: This field disp

Chapter 5 Troubleshooting If the ADSL2+ Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before

Frequent loss of ADSL linesync (disconnections). Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, f

APPENDIX Product Support and Contact Information Most problems can be solved by referring to the Troubleshooting section in the User’s Manual. If y

client IP addresses and distribute them including IP address, subnet mask as well as DNS IP address to local computers. It provides an easy way to man

1.3 Applications for the BIPAC 5102 Series 6

Chapter 2 Installing the BIPAC 5102 Series 2.1 Important note for using the BIPAC 5102 Series ADSL Router Warning  Do not use the BI